READ THIS FILE COMPLETELY BEFORE BEGINNING PRODUCT INSTALLATION
Copyright 1999 Compaq Computer Corporation

   Product Name:              ASAP Server

   Marketing Product ID:      SE30V1

   Component Products         T0402V01


I. Basic Product Installation Instructions

1. Ensure that requirements for using this product are met
   (see Section IV Product Requirements below).

2. Ensure that prerequisites for the installation utility and any
   product-specific installation requirements are met
   (see Section V Installation Prerequisites below).

3. Review the file USRGUIDE.PDF (in the subdirectory NSK_SW on this
   CD) containing the IPSetup User Guide, which provides instructions
   for using IPSetup, a utility provided on the CD that enables
   installation of Independent Products. You need Adobe Acrobat Reader
   (available on this CD) to read or print the IPSetup User Guide.

4. Decide whether you will use DSM/SCM to move files to Installation
   Subvolumes (ISVs) after files are placed on the workstation. Using
   DSM/SCM is optional, but is recommended when DSM/SCM is available.

5. Follow the pre-installation instructions in Section II below, if
   any, before continuing to Step 6.

6. Run IPSetup to place (move files from the CD to the workstation)
   and install (move NonStop Kernel files to correct ISVs) this
   product. If TCP/IP and FTP are unavailable, or if you have problems
   with automatic file placement, use the instructions in the IPSetup
   User Guide section "Manual Software Placement Using the IPSetup
   TACL Program" to manually place NonStop Kernel files.

7. Follow the post-installation instructions in Section III below, if
   any, after using IPSetup to place and install this product.

II.  Pre-Installation Instructions

        None

III. Post-Installation Instructions

     1) Invoke the INSTALL^TEMPLATES TACL macro to install this
        NPV's EMS template file(s) in the running system. This TACL
        macro and instructions for its use are given in Support Note
        S92067B.  The INSTALL^TEMPLATES TACL macro is distributed
        on the SUT and can be located in the ISV volume:
        $<ISVvol>.ZINSAIDS.TACLMACS. To print the usage notes,
        LOAD the file containing the macro and, at the TACL
        prompt, enter: INSTALL^TEMPLATES /OUT <outdev>/HELP

     2) Run ASAP setup to update the ASAP subsystem with the
        following commands:

        a) TACL 1 > VOLUME $<ISV-VOLUME>.ZASAP

        b) TACL 2 > OBEY INSTALL

        c) Perform "Full Install on this node" from the central ASAP
           database node.

        d) Perform "Remote Monitor Install" for any additional
           Licensed ASAP nodes that you wish to monitor. See Section 2
           of the ASAP manual for detailed information regarding
           subsystem configuration.

IV. Product Requirements

        Required Hardware:
                NonStop RISC-based servers

        Minimum OS Release:
                NonStop Kernel release D40.00 or higher
                NonStop Kernel release G03.00 or higher

        Required Software:
                T9057D40^ADE or
                T9057G02^ADY ,
                T9086D40^ACE or
                T9086G02^ABS ,
                T9117D40^AAW or
                T9117G02^AAV

        Disk Space Requirement:
                ZASAP subvol 2.0MB
                $System.system run time files 804KB
                ASAP Dictionary files 330KB
                Refer to the section 2 of the ASAP manual for ASAP
                database file sizes.

        Memory Requirement:
                16MB per cpu minimum.

V. Installation Prerequisites

        Required Hardware:
          Tandem NonStop server
          Communications controller allowing file transfer
                from PC to Tandem

          PC with 486 or higher processor and all of the following:
                CD-ROM drive
                VGA or higher-resolution video adapter and monitor
                Microsoft Mouse or similar pointing device
                Communications controller allowing file transfer
                        from PC to Tandem

        Required Software:
          T9550D30 SOCKET LIBRARY or higher version
          T9552D30 TCP/IP FTP with IPM ABG or superseding IPM
                (for releases D31.00 to D40.00)
          T9552D40 TCP/IP FTP with IPM ABJ or superseding IPM
                (for releases D40.01 and higher)

          Microsoft Windows 95, or Windows NT 4.0 or later
          Microsoft TCP/IP stack and FTP client

VI. Manuals Included On this CD

          422770 ASAP SERVER

VII. CD-ROM Root Directory Contents

AXDIST.EXE

AUTORUN.INF     File containing CD AutoRun commands

IPSETUP.CNT     File containing help contents for the CD installation
                utility IPSetup.

IPSETUP.EXE     File containing the main executable for IPSetup.

IPSETUP.HLP     File containing help text for IPSetup.

LICENSE.TXT     File containing limited-use Software Licensing
                Agreement with the licensing terms governing
                this product.

README.TXT      File containing product and installation information
                (this file).

SETUP.EXE       File containing the Launcher executable.

NSK_SW  Subdirectory containing NonStop Kernel component files,
        including installation utilities and instructions.


CD_DOCS Subdirectory containing product documentation in the
        following two subdirectories:

        TIM_COLL Subdirectory of CD_DOCS containing product manuals
                 formatted for the Tandem Information Manager (TIM)
                 viewer.

        PDF_DOCS Subdirectory of CD_DOCS containing:
                1. Product manuals in PDF format for viewing with
                   Adobe Acrobat Reader

                2. ACROBAT_VIEWERS subdirectory containing Adobe
                   Acrobat Reader for DOS, OS/2, Windows,
                   Windows NT, MacOS, Sun OS, Solaris, HP-UX,
                   IBM AIX, and SGI IRIX.